INDUSTRIAL OR MARINE ATMOSPHERE WITH TWO-COMPONENT SOLVENT EPOXY PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of epoxy galvanizer series 365, drying for 24 hours at 20 ° C
– 2nd base step: one coat of solvent epoxy primer series 364 or 370 or 373 or 377, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of epoxy solvent enamel series 611 or 613 or 616 or 621 or 656, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
INDUSTRIAL ATMOSPHERE WITH EPOXY BICOMPONENT WATER PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of epoxy galvanizer series 365, drying for 24 hours at 20 ° C
– 2nd base step: one coat of waterborne epoxy primer 363 series, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of water based epoxy enamel 661 or 697 series, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
INDUSTRIAL OR MARINE ATMOSPHERE WITH SOLVENT-BASED TWO-COMPONENT POLYURETHANE PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of epoxy galvanizer series 365, drying for 24 hours at 20 ° C
– 2nd base coat: one coat of solvent polyurethane primer series 375, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of solvent-based polyurethane enamel 630 or 638 or 639 or 655 or 658 or 686 or textured effect 624 or antique iron effect 620 or 619 or non-yellowing acrylic-polyurethane 614 or 612 or 610, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
INDUSTRIAL ATMOSPHERE WITH WATER-BASED BICOMPONENT POLYURETHANE PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of epoxy galvanizer Series 365, drying for 24 hours at 20 ° C
– 2nd base step: one coat of water-based polyurethane primer series 372, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of water-based polyurethane enamel 634 or 635 or 636 series, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
INDUSTRIAL ATMOSPHERE WITH SINGLE-COMPONENT SOLVENT PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of galvanizer series 321, drying for 24 hours at 20°C
– 2nd base step: one coat of one-component solvent-based primer series 308 or 317 or 319 or 324 or 371, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of fast-drying single-component solvent enamel series 500 or 502 or 503 or 521 or 525 or 528 or 531 or 535 or 539 or 556 or 582 or 585 or chlorinated rubber series 640 or 641 or 642 or nitro series 510, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
INDUSTRIAL ATMOSPHERE WITH SINGLE COMPONENT WATER-BASED PAINT ON SANDBLASTED IRON
– 1st protection phase: one coat of galvanizer Series 321, drying for 24 hours at 20°C
– 2nd intermediate step: one coat of one-component water-based primer series 330 or 335, drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of one-component water-based enamel 590 or 595 or 598 series, drying for 24 hours at 20°C.
N.B. on galvanized iron the first phase is skipped.
NORMAL ATMOSPHERE WITH TWO-COMPONENT SOLVENT EPOXY PAINT ON NON-BLASTED IRON
– Washing phase 1: clean the substrate from dirt and grease with thinner 7540000
– 2nd phase removal or conversion: in the presence of old varnish, remove it with LEVACOLOR code 7780000, in the presence of rust, remove it by sanding the surface or convert it to a protective layer with B3/F4. Dry for 24 hours at 20°C and then wash with water to eliminate any excess unreacted product.
– 3rd base step: one coat of solvent epoxy primer series 364 or 370 or 377, drying for 24 hours at 20°C
– 4th finishing phase: one or two coats of epoxy solvent enamel 611 or 616 or 621 series, drying for 24 hours at 20°C.
NORMAL ATMOSPHERE WITH TWO-COMPONENT POLYURETHANE PAINT ON NON-SANDBLASTED IRON
– Washing phase 1: clean the substrate from dirt and grease with thinner 7540000
– 2nd phase removal or conversion: in the presence of old varnish, remove it with LEVACOLOR code 7780000, in the presence of rust, remove it by sanding the surface or convert it to a protective layer with B3/F4. Dry for 24 hours at 20°C and then wash with water to eliminate any excess unreacted product.
– 3rd base step: one coat of solvent polyurethane primer series 375, drying for 24 hours at 20°C
– 4th finishing phase: one or two coats of solvent-based polyurethane enamel 630 series or acrylic-polyurethane enamel 552 or 554 or 555 series with micaceous effect 619 or 620 series, drying for 24 hours at 20°C.
NORMAL ATMOSPHERE WITH SINGLE COMPONENT SOLVENT PAINT ON NON-SANDBLASTED IRON
– Washing phase 1: clean the substrate from dirt and grease with thinner 7540000
– 2nd phase removal or conversion: in the presence of old varnish, remove it with LEVACOLOR code 7780000, in the presence of rust, remove it by sanding the surface or convert it to a protective layer with B3/F4. Dry for 24 hours at 20°C and then wash with water to eliminate any excess unreacted product.
– 3rd base step: one coat of zinc phosphate primer Series 300 or 303 or 308 or 326, drying for 24 hours at 20°C
– 4th finishing phase: one or two coats of fast-drying solvent enamel 528 series or synthetic enamel 210 or 211 or 212 or 222 series, drying for 24 hours at 20°C.
NORMAL ATMOSPHERE WITH SINGLE COMPONENT WATER-BASED PAINT ON NON-SANDBLASTED IRON
– Washing step 1: Clean dirt and grease from the substrate with thinner 7420000 or 7890000.
– 2nd phase removal or conversion: in the presence of old varnish, remove it with LEVACOLOR code 7780000, in the presence of rust, remove it by sanding the surface or convert it to a protective layer with B3/F4. Dry for 24 hours at 20°C and then wash with water to eliminate any excess unreacted product.
– 3rd base step: One coat of water-based primer series 330 or 340, drying for 24 hours at 20°C
– 4th topcoat: one or two coats of water-based enamel 590 or 591 or 592 or 593 or BIO 991 series, drying for 24 hours at 20°C.
NORMAL ATMOSPHERE WITH SINGLE COMPONENT SOLVENT PAINT ON GALVANIZED IRON
– Washing phase 1: clean the substrate from dirt and grease with thinner 7540000
– 2nd base step: one coat of 319 or 518 series adhesion primer (paintzinc), drying for 24 hours at 20°C
– 3rd finishing phase: one or two coats of fast-drying solvent enamel 528 series or synthetic enamel 210 or 211 or 212 or 222 series or antique iron effect 519 series, drying for 24 hours at 20°C.